Dobrica Pavlinušić's random unstructured stuff
ULX3S: Revision 16
Contents


first steps

Here I will try to document correct order to read documentation to get setup for ULX3S:

https://github.com/emard/ulx3s-bin/blob/master/README.md

udev rule

ujprog

git clone https://github.com/f32c/tools f32c-tools
cd f32c-tools/ujprog/
dpavlin@x200:/mnt/nuc/FPGA/f32c-tools/ujprog$ rm ujprog
dpavlin@x200:/mnt/nuc/FPGA/f32c-tools/ujprog$ make -f Makefile.linux
cc -Wall -D__linux__ -std=gnu99 -static ujprog.c /usr/lib/x86_64-linux-gnu/libftdi.a /usr/lib/x86_64-linux-gnu/libusb.a -o ujprog
dpavlin@x200:/mnt/nuc/FPGA/f32c-tools/ujprog$ sudo cp ujprog /usr/local/bin/

  • create udev rule

passthru to access esp32

dpavlin@x200:/mnt/nuc/FPGA/ulx3s-bin/fpga/passthru/passthru-v20-85f$ ujprog -j flash ulx3s_85f_passthru.bit
ULX2S / ULX3S JTAG programmer v 3.0.92 (built Nov 19 2019 10:55:50)
Using USB cable: ULX3S FPGA 12K v3.0.3
[Wed Nov 20 18:02:01 2019] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[Wed Nov 20 18:02:01 2019] ftdi_sio 1-5.2:1.0: device disconnected
Programming: 100%
Completed in 24.36 seconds.
[Wed Nov 20 18:02:25 2019] usb 1-5.2: reset full-speed USB device number 56 using ehci-pci
[Wed Nov 20 18:02:26 2019] ftdi_sio 1-5.2:1.0: FTDI USB Serial Device converter detected
[Wed Nov 20 18:02:26 2019] usb 1-5.2: Detected FT-X
[Wed Nov 20 18:02:26 2019] usb 1-5.2: FTDI USB Serial Device converter now attached to ttyUSB0

update size of your FPGA

dpavlin@x200:/mnt/nuc/FPGA/ulx3s-bin$ usb-jtag/linux-amd64/ftx_prog --product "ULX3S FPGA 85K v3.0.3"

power cycle board to get new usb id, test that it's supported by ujprog

dpavlin@x200:/mnt/nuc/FPGA/ulx3s-bin$ ujprog -r

esptool and esp32 booting problems

You should be using ecptool from ulx3s-bin repository to quite @emard from https://gitter.im/ulx3s/Lobby#dark-theme

OK then. If you have issues with ESP32 not booting with SD card but booting without SD card then then the fuse burn script from ulx3s-bin should be run. So far so good, you erased its flash, try linux. If no issue then can try to flash micropython and my new ESP32 OTA programmer ecp5.py end uftpd.py

I have wisely taken some esptool.py which works and frozen it in ulx3s, versions change all the time and maybe you took something in the middle of development action :)

install micropython

https://github.com/emard/esp32ecp5/

dpavlin@nuc:/nuc/FPGA$ git clone https://github.com/emard/esp32ecp5/
dpavlin@nuc:/nuc/FPGA$ cd esp32ecp5/
dpavlin@x200:/mnt/nuc/FPGA/esp32ecp5$ wget https://micropython.org/resources/firmware/esp32-idf3-20191120-v1.11-580-g973f68780.bin

It's important to erase flash or micropyhton will complain about corrupt fat filesystem like:

FAT filesystem appears to be corrupted. If you had important data there, you
may want to make a flash snapshot to try to recover it. Otherwise, perform
factory reprogramming of MicroPython firmware (completely erase flash, followed
by firmware programming).

dpavlin@x200:/mnt/nuc/FPGA/esp32ecp5$ ../ulx3s-bin/esp32/serial-uploader/esptool.py --chip esp32 --port /dev/ttyUSB0 erase_flash
esptool.py v2.6-beta1
Serial port /dev/ttyUSB0
Connecting....
Chip is ESP32D0WDQ6 (revision 1)
Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None
MAC: a4:cf:12:55:c5:60
Uploading stub...
Running stub...
Stub running...
Erasing flash (this may take a while)...
Chip erase completed successfully in 8.7s
Hard resetting via RTS pin...


dpavlin@x200:/mnt/nuc/FPGA/esp32ecp5$ ../ulx3s-bin/esp32/serial-uploader/esptool.py --chip esp32 --port /dev/ttyUSB0 --baud 460800 write_flash -z 0x1000 esp32-idf3-20191120-v1.11-580-g973f68780.bin
esptool.py v2.6-beta1
Serial port /dev/ttyUSB0
Connecting....
Chip is ESP32D0WDQ6 (revision 1)
Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None
MAC: a4:cf:12:55:c5:60
Uploading stub...
Running stub...
Stub running...
Changing baud rate to 460800
Changed.
Configuring flash size...
Auto-detected Flash size: 4MB
Compressed 1240192 bytes to 783187...
Wrote 1240192 bytes (783187 compressed) at 0x00001000 in 18.7 seconds (effective 529.3 kbit/s)...
Hash of data verified.

Leaving...
Hard resetting via RTS pin...

dpavlin@x200:/mnt/nuc/FPGA/esp32ecp5$ microcom -p /dev/ttyUSB0
connected to /dev/ttyUSB0
Escape character: Ctrl-\
Type the escape character to get to the prompt.

>>>
> help()
Welcome to MicroPython on the ESP32!

For generic online docs please visit http://docs.micropython.org/

For access to the hardware use the 'machine' module:

import machine
pin12 = machine.Pin(12, machine.Pin.OUT)
pin12.value(1)
pin13 = machine.Pin(13, machine.Pin.IN, machine.Pin.PULL_UP)
print(pin13.value())
i2c = machine.I2C(scl=machine.Pin(21), sda=machine.Pin(22))
i2c.scan()
i2c.writeto(addr, b'1234')
i2c.readfrom(addr, 4)

Basic WiFi configuration:

import network
sta_if = network.WLAN(network.STA_IF); sta_if.active(True)
sta_if.scan()                             # Scan for available access points
sta_if.connect("<AP_name>", "<password>") # Connect to an AP
sta_if.isconnected()                      # Check for successful connection

Control commands:
  CTRL-A        -- on a blank line, enter raw REPL mode
  CTRL-B        -- on a blank line, enter normal REPL mode
  CTRL-C        -- interrupt a running program
  CTRL-D        -- on a blank line, do a soft reset of the board
  CTRL-E        -- on a blank line, enter paste mode

For further help on a specific object, type help(obj)
For a list of available modules, type help('modules')

webrepl

dpavlin@klin:/klin/FPGA$ git clone https://github.com/hyperglitch/webrepl

You can send files from command-line:

dpavlin@x200:/mnt/nuc/FPGA/webrepl$ ./webrepl_cli.py -p ulx3s ../esp32ecp5/ecp5.py 192.168.3.130:/
op:put, host:192.168.3.130, port:8266, passwd:ulx3s.
../esp32ecp5/ecp5.py -> /ecp5.py
Remote WebREPL version: (1, 11, 0)
Sent 22777 of 22777 bytes
dpavlin@x200:/mnt/nuc/FPGA/webrepl$ ./webrepl_cli.py -p ulx3s ../esp32ecp5/uftpd.py 192.168.3.130:/
op:put, host:192.168.3.130, port:8266, passwd:ulx3s.
../esp32ecp5/uftpd.py -> /uftpd.py
Remote WebREPL version: (1, 11, 0)
Sent 19482 of 19482 bytes

open source toolchain

this is old and needs update

dpavlin@klin:/klin/FPGA$ git clone https://github.com/SymbiFlow/prjtrellis
dpavlin@klin:/klin/FPGA/prjtrellis$ ./download-latest-db.sh 

dpavlin@klin:/klin/FPGA/prjtrellis$ cd libtrellis/
dpavlin@klin:/klin/FPGA/prjtrellis/libtrellis$ sudo apt-get install libpython3-dev libboost-python-dev libboost-filesystem-dev libboost-thread-dev libboost-program-options-dev
dpavlin@klin:/klin/FPGA/prjtrellis/libtrellis$ cmake -DCMAKE_INSTALL_PREFIX=/usr/local .
dpavlin@klin:/klin/FPGA/prjtrellis/libtrellis$ make

diamond

https://github.com/jandob/lattice-diamond-archlinux/blob/master/eth0DummyToggle

saxxonsoc

linux

https://gitter.im/ulx3s/Lobby?at=5de8ba2f08d0c961b7f3a25f

git clone https://github.com/SpinalHDL/buildroot.git -b saxon buildroot
git clone https://github.com/SpinalHDL/linux.git -b vexriscv --depth 1 linux
cd buildroot
cp board/spinal/saxon_default/linux_nonet.config board/spinal/saxon_default/linux.config
# Add extra options to board/spinal/saxon_default/linux.config
make spinal_saxon_default_defconfig
make linux-rebuild all -j$(nproc)
output/host/bin/riscv32-linux-objcopy -O binary output/images/vmlinux output/images/Image
# Make sure Image is at least 116KB less than 4MB

85f version

https://gitter.im/ulx3s/Lobby?at=5dea74995ac7f22fb57055ae

https://github.com/lawrie/saxonsoc-ulx3s-bin/blob/master/linux/README.md

NES

https://gitter.im/ulx3s/Lobby?at=5de033f49319bb5190a9c3b6