Dobrica Pavlinušić's random unstructured stuff
Printrbot Plus: Revision 13
{file: Printrboard-schematics.pdf}
Old 3D printer which never worked well. https://web.archive.org/web/20130115210644/http://printrbot.com/shop/plus/ {toc: } ^ PrintrBot Plus The Printrbot PLUS is the larger printrbot kit–containing an 8x8x8 build volume, laser cut birch construction, an assembled Ubis hot end, and 12mm Z-axis rods in an all-in-one kit. This kit also includes 1 lb of ABS filament. This kit includes everything you need to build the printrbot PLUS: NEW: Power Supply Included! printrboard: all-in-one assembled electronics with integrated SD card slot (no soldering required) 5 NEMA 17 stepper motors complete with cable ends attached laser cut birch construction a few printed plastic parts (gears, etc) WOOD Extruder Kit hardware (8mm smooth rods, threaded rods, and bearings — ** Z axis is 12mm smooth rods and 12 mm linear bearings ) assembled Ubis hot end nuts, bolts, washers, zip ties laser cut print bed 8×8 heated bed misc assembled cables (no soldering required) 3 mechanical end stops (no soldering required) micro USB cable (Glass for heated bed not included ) ^ info Most of information about it vanished from internet so here is some overview: * http://reprap.org/wiki/Printrbot * http://reprap.org/wiki/Printrboard * https://github.com/Printrbot/printrboard Rev.B https://github.com/Printrbot/printrboard/releases/tag/revB ^ serial .pre [Sun Mar 18 08:23:50 2018] usb 2-4.4: new full-speed USB device number 61 using xhci_hcd [Sun Mar 18 08:23:50 2018] usb 2-4.4: New USB device found, idVendor=16c0, idProduct=0483 [Sun Mar 18 08:23:50 2018] usb 2-4.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [Sun Mar 18 08:23:50 2018] usb 2-4.4: Product: USB Serial [Sun Mar 18 08:23:50 2018] usb 2-4.4: Manufacturer: Teensyduino [Sun Mar 18 08:23:50 2018] usb 2-4.4: SerialNumber: 12345 [Sun Mar 18 08:23:50 2018] cdc_acm 2-4.4:1.0: ttyACM0: USB ACM device dpavlin@nuc:~$ microcom p /dev/ttyACM0 connected to /dev/ttyACM0 Escape character: Ctrl\ Type the escape character to get to the prompt. echo:SD init fail workDir open failed echo:Unknown command:"echo" ok echo:Unknown command:"SD init fail" ok echo:Unknown command:"workDir open failed" ok .pre ^ settings https://github.com/Printrbot/Marlin .pre M501 echo:Stored settings retreived: echo:Steps per unit: echo: M92 X62.11 Y64.67 Z2272.72 E536.00 echo:Maximum feedrates (mm/s): echo: M203 X60.00 Y60.00 Z2.00 E14.00 echo:Maximum Acceleration (mm/s2): echo: M201 X2000 Y2000 Z30 E10000 echo:Acceleration: S=acceleration, T=retract acceleration echo: M204 S3000.00 T3000.00 echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum xY jerk (mm/s), Z=maximum Z jerk (mm/s) echo: M205 S0.00 T0.00 B20000 X20.00 Z0.40 E5.00 echo:PID settings: echo: M301 P22.20 I1.08 D114.00 M115 FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:http://www.mendel-parts.com PROTOCOL_VERSION:1.0 MACHINE_TYPE:Mendel EXTRUDER_COUNT:1 .pre ^ software bed leveler * https://github.com/emard/zleveler ^ schematics {image: Printrboard_RevB_Schematic150.png} |