|
Dobrica Pavlinušić's random unstructured stuff
USB armory Mk II: Revision 24
SoC: NXP i.MX6ULZ ARM® Cortex™-A7 900 MHz Wiki which claims that there is binary release for Mk II is lying. You have to compile your own. https://github.com/inversepath/usbarmory-debian-base_image
dpavlin@klin:~/usb-armory/usbarmory-debian-base_image$ ls -al usbarmory-mark-two-debian_stretch-base_image-20191013.raw
-rw-r--r-- 1 root root 3670016000 Oct 13 13:30 usbarmory-mark-two-debian_stretch-base_image-20191013.raw
dpavlin@nuc:/mnt/klin/home/dpavlin/usb-armory/usbarmory-debian-base_image$ dd if=usbarmory-mark-two-debian_stretch-base_image-20191013.raw of=/dev/sdb bs=1M
dpavlin@nuc:~$ dmesg
[764607.538898] usb 2-1: new high-speed USB device number 34 using xhci_hcd
[764607.689068] usb 2-1: New USB device found, idVendor=0525, idProduct=a4a2, bcdDevice= 4.19
[764607.689078] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[764607.689082] usb 2-1: Product: RNDIS/Ethernet Gadget
[764607.689100] usb 2-1: Manufacturer: Linux 4.19.78-0 with 2184000.usb
[764607.900916] cdc_subset: probe of 2-1:1.0 failed with error -22
[764607.902622] cdc_subset 2-1:1.1 usb0: register 'cdc_subset' at usb-0000:00:14.0-1, Linux Device, ae:47:47:81:a0:a4
[764607.902666] usbcore: registered new interface driver cdc_subset
[764607.902711] cdc_ether: probe of 2-1:1.0 failed with error -16
[764607.902732] usbcore: registered new interface driver cdc_ether
[764607.914234] cdc_subset 2-1:1.1 enp0s20u1i1: renamed from usb0
dpavlin@nuc:~$ sudo ifconfig enp0s20u1i1 10.0.0.2 netmask 255.255.255.0
dpavlin@nuc:~$ sudo iptables -t nat -A POSTROUTING -s 10.0.0.0/24 -o eth0 -j MASQUERADE
dpavlin@nuc:~$ ssh usbarmory@10.0.0.1
# password is usbarmory
usbarmory@usbarmory:~$ uname -a
Linux usbarmory 4.19.78-0 #1 PREEMPT Sun Oct 13 11:05:18 UTC 2019 armv7l GNU/Linux
usbarmory@usbarmory:~$ cat /proc/cpuinfo
processor : 0
model name : ARMv7 Processor rev 5 (v7l)
BogoMIPS : 109.09
Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae
CPU implementer : 0x41
CPU architecture: 7
CPU variant : 0x0
CPU part : 0xc07
CPU revision : 5
Hardware : Freescale i.MX6 Ultralite (Device Tree)
Revision : 0000
Serial : 0000000000000000
usbarmory@usbarmory:~$ free
total used free shared buff/cache available
Mem: 512204 25588 436744 7624 49872 467984
Swap: 0 0 0
boot select switchSwitch near sdcard select booting from emmc or microsd (silkscreen is somewhat poor, but by default bafore removing sticker it will boot from sdcard) If it's closer to sdcard, it will boot from sdcard image delivered on devicePassword for image delivered with device is not usbarmory (?) In fact, it doesn't have usbarmory user in /etc/passwd, but has it in /etc/shadow, go figure! root@usbarmory:/# cat /etc/passwd root:x:0:0:root:/root:/bin/bash daemon:x:1:1:daemon:/usr/sbin:/usr/sbin/nologin bin:x:2:2:bin:/bin:/usr/sbin/nologin sys:x:3:3:sys:/dev:/usr/sbin/nologin sync:x:4:65534:sync:/bin:/bin/sync games:x:5:60:games:/usr/games:/usr/sbin/nologin man:x:6:12:man:/var/cache/man:/usr/sbin/nologin lp:x:7:7:lp:/var/spool/lpd:/usr/sbin/nologin mail:x:8:8:mail:/var/mail:/usr/sbin/nologin news:x:9:9:news:/var/spool/news:/usr/sbin/nologin uucp:x:10:10:uucp:/var/spool/uucp:/usr/sbin/nologin proxy:x:13:13:proxy:/bin:/usr/sbin/nologin www-data:x:33:33:www-data:/var/www:/usr/sbin/nologin backup:x:34:34:backup:/var/backups:/usr/sbin/nologin list:x:38:38:Mailing List Manager:/var/list:/usr/sbin/nologin irc:x:39:39:ircd:/var/run/ircd:/usr/sbin/nologin gnats:x:41:41:Gnats Bug-Reporting System (admin):/var/lib/gnats:/usr/sbin/nologin nobody:x:65534:65534:nobody:/nonexistent:/usr/sbin/nologin systemd-timesync:x:100:102:systemd Time Synchronization,,,:/run/systemd:/bin/false systemd-network:x:101:103:systemd Network Management,,,:/run/systemd/netif:/bin/false systemd-resolve:x:102:104:systemd Resolver,,,:/run/systemd/resolve:/bin/false systemd-bus-proxy:x:103:105:systemd Bus Proxy,,,:/run/systemd:/bin/false _apt:x:104:65534::/nonexistent:/bin/false messagebus:x:105:108::/var/run/dbus:/bin/false sshd:x:106:65534::/run/sshd:/usr/sbin/nologin interlock:x:1000:1000::/home/interlock:/bin/bash lcars:x:1001:1001::/home/lcars:/bin/bash root@usbarmory:/# cat /etc/shadow root:*:18068:0:99999:7::: daemon:*:18068:0:99999:7::: bin:*:18068:0:99999:7::: sys:*:18068:0:99999:7::: sync:*:18068:0:99999:7::: games:*:18068:0:99999:7::: man:*:18068:0:99999:7::: lp:*:18068:0:99999:7::: mail:*:18068:0:99999:7::: news:*:18068:0:99999:7::: uucp:*:18068:0:99999:7::: proxy:*:18068:0:99999:7::: www-data:*:18068:0:99999:7::: backup:*:18068:0:99999:7::: list:*:18068:0:99999:7::: irc:*:18068:0:99999:7::: gnats:*:18068:0:99999:7::: nobody:*:18068:0:99999:7::: systemd-timesync:*:18068:0:99999:7::: systemd-network:*:18068:0:99999:7::: systemd-resolve:*:18068:0:99999:7::: systemd-bus-proxy:*:18068:0:99999:7::: _apt:*:18068:0:99999:7::: messagebus:*:18068:0:99999:7::: sshd:*:18068:0:99999:7::: usbarmory:$6$rcyB4m4EPv$udqWloCZH/Av1IkJVuZHyWMhw/fYkhLGevlo17C3x6qMemSHUmPPAQrvc0SaY.yWVIIU0ADL0g54MZmidcxFn.:18068:0:99999:7::: lcars:$6$iFljmotV$gnK66oZpz7BD3BqlFpPWoY/Q1tey8in75868neosxypKswjSoNDQotiMBZ9hh.vQBDyltA08z2Vji/QjElv4g.:18072:0:99999:7::: interlock:!:18072:0:99999:7::: After adding usbarmory account, running apt upgrade (since image has old kernel) device isn't bootable any more (at least it's not detected by host in which it's plugged in). Let's try to rebuild image for emmc and flash it. Well, re-build fails with patches allready applied errors in linux source, so let's wipe it: root@813046ba7c77:/opt/armory# rm -Rf linux-* u-boot-2019.07* root@813046ba7c77:/opt/armory# make all V=mark-two IMX=imx6ull BOOT=eMMC -j 8 pads on boarddocumentation again claims that schematics is available, but it isn't for mk2 https://github.com/inversepath/usbarmory/tree/master/hardware from changelog thouse pads might be jtag (since it's enabled in u-boot), but without schematics who knows... It seems that 8 gpio pins are available using additional board: https://github.com/inversepath/usbarmory/tree/master/hardware/mark-two-debug-accessory sdcard vs emmc speedroot@usbarmory:/mnt/klin/home/dpavlin/usb-armory/usbarmory-debian-base_image# hdparm -Tt /dev/mmcblk[01] /dev/mmcblk0: # -- sdcard Timing cached reads: 664 MB in 2.00 seconds = 331.99 MB/sec Timing buffered disk reads: 34 MB in 3.03 seconds = 11.21 MB/sec /dev/mmcblk1: # -- emmc Timing cached reads: 716 MB in 2.00 seconds = 357.40 MB/sec Timing buffered disk reads: 128 MB in 3.04 seconds = 42.17 MB/sec communityhttps://groups.google.com/forum/#!forum/usbarmory led heartbeat offhttps://photos.app.goo.gl/rRrzfbbs4GGjt3ePA very bright and annoying in dark room sbarmory@usbarmory:/sys/class/leds/LED_WHITE$ cat trigger none kbd-scrolllock kbd-numlock kbd-capslock kbd-kanalock kbd-shiftlock kbd-altgrlock kbd-ctrllock kbd-altlock kbd-shiftllock kbd-shiftrlock kbd-ctrlllock kbd-ctrlrlock mmc0 mmc1 cpu cpu0 [heartbeat] root@usbarmory:/sys/devices/soc0/leds/leds/LED_WHITE# echo none > trigger nwtwork speedroot@usbarmory:~# iperf3 -c 10.0.0.2 Connecting to host 10.0.0.2, port 5201 [ 4] local 10.0.0.1 port 33574 connected to 10.0.0.2 port 5201 [ ID] Interval Transfer Bandwidth Retr Cwnd [ 4] 0.00-1.03 sec 23.0 MBytes 188 Mbits/sec 0 174 KBytes [ 4] 1.03-2.00 sec 20.6 MBytes 178 Mbits/sec 0 272 KBytes [ 4] 2.00-3.01 sec 21.1 MBytes 176 Mbits/sec 0 286 KBytes [ 4] 3.01-4.01 sec 21.8 MBytes 182 Mbits/sec 0 297 KBytes [ 4] 4.01-5.00 sec 20.1 MBytes 171 Mbits/sec 0 297 KBytes [ 4] 5.00-6.00 sec 21.0 MBytes 176 Mbits/sec 0 329 KBytes [ 4] 6.00-7.00 sec 20.3 MBytes 171 Mbits/sec 0 329 KBytes [ 4] 7.00-8.00 sec 20.4 MBytes 171 Mbits/sec 0 329 KBytes [ 4] 8.00-9.00 sec 20.3 MBytes 171 Mbits/sec 0 329 KBytes [ 4] 9.00-10.00 sec 20.1 MBytes 169 Mbits/sec 0 329 KBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-10.00 sec 209 MBytes 175 Mbits/sec 0 sender [ 4] 0.00-10.00 sec 208 MBytes 174 Mbits/sec receiver iperf Done. bluetoothhttps://github.com/inversepath/usbarmory/wiki/Bluetooth root@usbarmory:/home/usbarmory# microcom -p /dev/ttymxc0 AT+GMR "1.0.0-017" armoryctlno binary in package, requires 1.12 go (which isn't in debian unstabne as of now) dpavlin@klin:~/usb-armory$ git clone https://github.com/inversepath/armoryctl dpavlin@klin:~/usb-armory/armoryctl$ make armoryctl GOARCH=arm github.com/inversepath/armoryctl/anna_b112 # github.com/inversepath/armoryctl/anna_b112 anna_b112/openocd.go:328:9: undefined: strings.ReplaceAll anna_b112/openocd.go:329:8: undefined: strings.ReplaceAll note: module requires Go 1.12make: *** [Makefile:27: armoryctl] Error 2 i2c
root@usbarmory:/home/usbarmory# i2cdetect -l
root@usbarmory:/home/usbarmory# modprobe i2c-dev
root@usbarmory:/home/usbarmory# i2cdetect -l
i2c-0 i2c 21a0000.i2c I2C adapter
root@usbarmory:/home/usbarmory# i2cdetect -y 0
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- 08 -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- 31 -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- 48 -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: 60 61 -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
|