|
Dobrica Pavlinušić's random unstructured stuff
Arduino: Revision 14
Nano 3.0 Atmega328P-AUhttp://dx.com/p/arduino-nano-v3-0-81877 but it doesn't work without bootloader
http://club.dx.com/forums/forums.dx/threadid.1185512 avrdude
dpavlin@blue:~$ avrdude -c buspirate -P /dev/ttyUSB0 -p m328p -v
avrdude: Version 5.11.1, compiled on Mar 24 2013 at 00:54:55
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2009 Joerg Wunsch
System wide configuration file is "/etc/avrdude.conf"
User configuration file is "/home/dpavlin/.avrduderc"
User configuration file does not exist or is not a regular file, skipping
Using Port : /dev/ttyUSB0
Using Programmer : buspirate
AVR Part : ATMEGA328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : BusPirate
Description : The Bus Pirate
Detecting BusPirate...
avrdude: buspirate_readline(): #
avrdude: buspirate_readline(): RE
avrdude: buspirate_readline(): Bus Pirate v3.b clone w/different PIC
avrdude: buspirate_readline(): Firmware v6.1 r1676 Bootloader v4.4
avrdude: buspirate_readline(): DEVID:0x044F REVID:0x3003 (24FJ64GA004 A3)
avrdude: buspirate_readline(): http://dangerousprototypes.com
avrdude: buspirate_readline(): HiZ>
**
BusPirate: using BINARY mode
BusPirate binmode version: 1
BusPirate SPI version: 1
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.01s
avrdude: Device signature = 0x1e950f
avrdude: safemode: lfuse reads as 62
avrdude: safemode: hfuse reads as D9
avrdude: safemode: efuse reads as 7
avrdude: safemode: lfuse reads as 62
avrdude: safemode: hfuse reads as D9
avrdude: safemode: efuse reads as 7
avrdude: safemode: Fuses OK
BusPirate is back in the text mode
avrdude done. Thank you.
bootloader updatehttp://dangerousprototypes.com/docs/Bus_Pirate_AVR_Programming But which bootloader to use? (hint: not optiboot!) dpavlin@blue:~$ ard-parse-boards nano328 bootloader.file ATmegaBOOT_168_atmega328.hex Ok, now flash it!
dpavlin@blue:~$ avrdude -c buspirate -P /dev/ttyUSB0 -p m328p -U flash:w:/usr/share/arduino/hardware/arduino/bootloaders/atmega/ATmegaBOOT_168_atmega328.hex
Detecting BusPirate...
**
BusPirate: using BINARY mode
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.01s
avrdude: Device signature = 0x1e950f
avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "/usr/share/arduino/hardware/arduino/bootloaders/atmega/ATmegaBOOT_168_atmega328.hex"
avrdude: input file /usr/share/arduino/hardware/arduino/bootloaders/atmega/ATmegaBOOT_168_atmega328.hex auto detected as Intel Hex
avrdude: writing flash (32670 bytes):
Writing | ################################################## | 100% 56.84s
avrdude: 32670 bytes of flash written
avrdude: verifying flash memory against /usr/share/arduino/hardware/arduino/bootloaders/atmega/ATmegaBOOT_168_atmega328.hex:
avrdude: load data flash data from input file /usr/share/arduino/hardware/arduino/bootloaders/atmega/ATmegaBOOT_168_atmega328.hex:
avrdude: input file /usr/share/arduino/hardware/arduino/bootloaders/atmega/ATmegaBOOT_168_atmega328.hex auto detected as Intel Hex
avrdude: input file /usr/share/arduino/hardware/arduino/bootloaders/atmega/ATmegaBOOT_168_atmega328.hex contains 32670 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 55.22s
avrdude: verifying ...
avrdude: 32670 bytes of flash verified
avrdude: safemode: Fuses OK
avrdude done. Thank you.
After re-flash using bus pirate as ISP from Arduino GUI fuses changed: avrdude: safemode: lfuse reads as FF avrdude: safemode: hfuse reads as DA avrdude: safemode: efuse reads as 5 avrdude: safemode: Fuses OK add bus pirate to arduino GUIhttp://taylanayken.wordpress.com/2011/05/04/using-bus-pirate-with-arduino-ide/ root@blue:~# grep buspirate /usr/share/arduino/hardware/arduino/programmers.txt buspirate.name=The Bus Pirate buspirate.communication=serial buspirate.protocol=buspirate Simulators/Emulatorsemulinoconsole output, somewhat large network on github https://github.com/ghewgill/emulino simuinoncurses interface, single stepping, doesn't have source control link, can't compile it http://code.google.com/p/simuino/ emulareRequres .net, need to test it with mono http://emulare.sourceforge.net/ simavr |