arduino boot loader

https://github.com/rogerclarkmelbourne/Arduino_STM32/wiki/Flashing-Bootloader-for-BluePill-Boards

triple usb serial

pill_serial

Function	Pin and Port
USART3 TX	PB10
USART3 RX	PB11
USART2 TX	PA2
USART2 RX	PA3
USART1 TX	PA9
USART1 RX	PA10

USART	TX pin	RX pin	special	speed	sensor	linux
3	PB10	PB11		9600	MH-Z19B	/dev/ttyACM1
2	PA2	PA3		9600
1	PA9	PA10	BOOT=0	9600

dpavlin@nuc:/nuc/stm32/pill_serial$ cat flash.sh
sudo ../stlink/build/Release/st-flash write src/pill_serial.bin 0x08000000

lower serial speed to 9600 so we can use slow sensors on it: serial-speed.diff

bluepill-serial-monster

https://github.com/r2axz/bluepill-serial-monster

openocd with raspberry pi

http://git.rot13.org/?p=openocd-rpi2-stm32;a=blob;f=openocd-rpi.txt

clones

https://github.com/thanks4opensource/buck50/issues/2

https://github.com/keirf/Greaseweazle/wiki/STM32-Fakes

dpavlin@nuc:/nuc/stm32/Greaseweazle$ wget https://github.com/keirf/Greaseweazle/releases/download/v0.22/Greaseweazle-v0.22.zip

dpavlin@nuc:/nuc/stm32/Greaseweazle$ unzip Greaseweazle-v0.22.zip Greaseweazle-v0.22/alt/Blinky_Test-v0.22.hex
Archive:  Greaseweazle-v0.22.zip
  inflating: Greaseweazle-v0.22/alt/Blinky_Test-v0.22.hex

write it to flash using openocd

> flash write_image erase /nuc/stm32/Greaseweazle/Greaseweazle-v0.22/alt/Blinky_Test-v0.22.hex 0 ihex
auto erase enabled
wrote 5120 bytes from file /nuc/stm32/Greaseweazle/Greaseweazle-v0.22/alt/Blinky_Test-v0.22.hex in 0.299529s (16.693 KiB/s)

serial output is on the programming interface at pins A9/TX and A10/RX: Not via the USB port!

pi@pihdmi:/nuc/stm32/buck50 $ microcom -p /dev/ttyUSB1
connected to /dev/ttyUSB1
Escape character: Ctrl-\
Type the escape character to get to the prompt.

** Blinky
** Blinky Test **
** Keir Fraser <keir.xen@gmail.com>
** https://github.com/keirf/Greaseweazle
Serial = ff48:0670:8967:5655:4740:6706
Flash Size  = 128kB
Device ID = 0x0000
Revision  = 0x0000
Testing I2C1... OK
Testing I2C2... OK
Testing SPI1... OK
Testing SPI2... OK
Testing TIM1... OK
Testing TIM2... OK
Testing TIM3... OK
Testing TIM4... OK
DMA Test #1... OK
DMA Test #2... OK
DMA Test #3... OK
DMA Test #4... OK
Testing 64kB Flash... OK
Enable TIM4 IRQ... .OK
Testing 20kB SRAM (endless loop)................................................................

After flashing this test, you will not be able to address blue pill using openocd.