Dobrica Pavlinušić's random unstructured stuff
CubieBoard: Revision 66
cubieboard_schematic_2012-08-08.pdf

BreadBoard V1.0 03-25 For CubieBoard.pdf



A20

Running UBI/UBIFS on MLC NAND

NAND in mainline kernel

Samsung K9GBG08U0A NAND

dpavlin@cubieboard:~$ dmesg | grep -A 5 nand
[    4.395437] nand: Could not find valid JEDEC parameter page; aborting
[    4.401898] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xd7
[    4.408272] nand: Samsung NAND 4GiB 3,3V 8-bit
[    4.412719] nand: 4096 MiB, MLC, erase size: 1024 KiB, page size: 8192, OOB size: 640
[    4.421299] Bad block table found at page 524160, version 0x25
[    4.427987] Bad block table found at page 524032, version 0x25
[    4.434238] nand_read_bbt: bad block at 0x000001000000
[    4.439379] nand_read_bbt: bad block at 0x000001100000
[    4.445411] 6 ofpart partitions found on MTD device 1c03000.nand
[    4.451420] Creating 6 MTD partitions on "1c03000.nand":
[    4.456769] 0x000000a00000-0x0001ffa00000 : "rootfs"
[    4.461737] mtd: partition "rootfs" extends beyond the end of device "1c03000.nand" -- size truncated to 0xff600000
[    4.472910] 0x000001000000-0x000001400000 : "env"
[    4.477926] 0x000000c00000-0x000001000000 : "U-Boot.backup"
[    4.483748] 0x000000800000-0x000000c00000 : "U-Boot"
[    4.488997] 0x000000400000-0x000000800000 : "SPL.backup"
[    4.494580] 0x000000000000-0x000000400000 : "SPL"



dpavlin@cubieboard2:~$ dmesg | grep -A 5 nand
[    4.709427] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xd7
[    4.715876] nand: Hynix H27UBG8T2BTR-BC 32G 3.3V 8-bit
[    4.721021] nand: 4096 MiB, MLC, erase size: 2048 KiB, page size: 8192, OOB size: 640
[    4.728997] Scanning device for bad blocks
[    8.484659] 6 ofpart partitions found on MTD device 1c03000.nand
[    8.490678] Creating 6 MTD partitions on "1c03000.nand":
[    8.496021] 0x000000a00000-0x0001ffa00000 : "rootfs"
[    8.500992] mtd: partition "rootfs" extends beyond the end of device "1c03000.nand" -- size truncated to 0xff600000
[    8.515527] 0x000001000000-0x000001400000 : "env"
[    8.520564] 0x000000c00000-0x000001000000 : "U-Boot.backup"
[    8.526504] 0x000000800000-0x000000c00000 : "U-Boot"
[    8.531755] 0x000000400000-0x000000800000 : "SPL.backup"
[    8.537395] 0x000000000000-0x000000400000 : "SPL"

many bad blocks

http://linux-sunxi.org/Mainline_NAND_Howto#Many_bad_blocks

To fix many bad blocks issue you should:

1. Disable nand-on-flash-bbt in your dts
2. Remove this test: http://lxr.free-electrons.com/source/drivers/mtd/nand/nand_base.c?v=4.7#L2940
3. Boot your new kernel and erase chip with flash_erase /dev/mtd[0-X]
4. Re-introduce the bad block check removed in 2, re-enable nand-on-flash-bbt
   and boot the new kernel

Let's try to do this with armbian.

cubieboard

First, enable nand overlay

dpavlin@cubieboard:~$ cat /boot/armbianEnv.txt
overlays=nand

Then remove nand-om-flash-btt:

dpavlin@cubieboard:/$ cd /boot/dtb-`uname -r`/overlay
dpavlin@cubieboard:/boot/dtb-4.14.23-sunxi/overlay$ 

# backup original
root@cubieboard:/boot/dtb-4.14.23-sunxi/overlay# cp sun4i-a10-nand.dtbo sun4i-a10-nand.dtbo.orig

# remote nand-on-flash-bbt
root@cubieboard:/boot/dtb-4.14.23-sunxi/overlay# dtc -I dtb -O dts sun4i-a10-nand.dtbo | grep -v nand-on-flash-bbt > /tmp/nand.dts
root@cubieboard:/boot/dtb-4.14.23-sunxi/overlay# dtc -I dts -O dtb /tmp/nand.dts > sun4i-a10-nand.dtbo

Compile armbian kernel with this patch applied

dpavlin@armbian:~/build$ cp ./patch/kernel/sunxi-dev/nand-disable-badblock-check-for-migration.patch.disabled \
    ./userpatches/kernel/sunxi-next/nand-disable-badblock-check-for-migration.patch

Reboot and check that nand is available:

dpavlin@cubieboard:~$ dmesg | grep -A 8 MTD
[   13.696198] 6 ofpart partitions found on MTD device 1c03000.nand
[   13.702205] Creating 6 MTD partitions on "1c03000.nand":
[   13.707550] 0x000000a00000-0x0001ffa00000 : "rootfs"
[   13.712517] mtd: partition "rootfs" extends beyond the end of device "1c03000.nand" -- size truncated to 0xff600000
[   13.723693] 0x000001000000-0x000001400000 : "env"
[   13.728713] 0x000000c00000-0x000001000000 : "U-Boot.backup"
[   13.734568] 0x000000800000-0x000000c00000 : "U-Boot"
[   13.739778] 0x000000400000-0x000000800000 : "SPL.backup"
[   13.745368] 0x000000000000-0x000000400000 : "SPL"
[   13.751476] sun4i-mdio 1c0b080.mdio: 1c0b080.mdio supply phy not found, using dummy regulator

Now init nand:

root@cubieboard:~# mtd_debug info /dev/mtd0
mtd.type = MTD_MLCNANDFLASH
mtd.flags = MTD_CAP_NANDFLASH
mtd.size = 4284481536 (3G)
mtd.erasesize = 1048576 (1M)
mtd.writesize = 8192 (8K)
mtd.oobsize = 640 
regions = 0


root@cubieboard2:~# mtd_debug info /dev/mtd0
mtd.type = MTD_MLCNANDFLASH
mtd.flags = MTD_CAP_NANDFLASH
mtd.size = 4284481536 (3G)
mtd.erasesize = 2097152 (2M)
mtd.writesize = 8192 (8K)
mtd.oobsize = 640 
regions = 0

root@cubieboard:/home/dpavlin# flash_erase /dev/mtd0 0 0
Erasing 1024 Kibyte @ 600000 --  0 % complete libmtd: error!: MEMERASE64 ioctl failed for eraseblock 6 (mtd0)
        error 5 (Input/output error)
flash_erase: error!: /dev/mtd0: MTD Erase failure
             error 5 (Input/output error)
Erasing 1024 Kibyte @ 700000 --  0 % complete libmtd: error!: MEMERASE64 ioctl failed for eraseblock 7 (mtd0)
        error 5 (Input/output error)
flash_erase: error!: /dev/mtd0: MTD Erase failure
             error 5 (Input/output error)
Erasing 1024 Kibyte @ ff500000 -- 100 % complete 


root@cubieboard:/home/dpavlin# ubiformat /dev/mtd0
ubiformat: mtd0 (mlc-nand), size 4284481536 bytes (4.0 GiB), 4086 eraseblocks of 1048576 bytes (1024.0 KiB), min. I/O size 8192 bytes
libscan: scanning eraseblock 4085 -- 100 % complete  
ubiformat: 4084 eraseblocks are supposedly empty
ubiformat: warning!: 2 of 4086 eraseblocks contain non-UBI data
ubiformat: continue? (y/N) y
ubiformat: warning!: only 0 of 4086 eraseblocks have valid erase counter
ubiformat: erase counter 0 will be used for all eraseblocks
ubiformat: note, arbitrary erase counter value may be specified using -e option
ubiformat: continue? (y/N) y
ubiformat: use erase counter 0 for all eraseblocks
ubiformat: formatting eraseblock 6 --  0 % complete  libmtd: error!: MEMERASE64 ioctl failed for eraseblock 6 (mtd0)
        error 5 (Input/output error)

ubiformat: error!: failed to erase eraseblock 6
           error 5 (Input/output error)
ubiformat: mark it as bad? (y/N) y
ubiformat: marking block 6 bad
ubiformat: formatting eraseblock 7 --  0 % complete  libmtd: error!: MEMERASE64 ioctl failed for eraseblock 7 (mtd0)
        error 5 (Input/output error)

ubiformat: error!: failed to erase eraseblock 7
           error 5 (Input/output error)
ubiformat: mark it as bad? (y/N) y
ubiformat: marking block 7 bad
ubiformat: formatting eraseblock 4085 -- 100 % complete  




ubiattach -p /dev/mtd0

ubimkvol /dev/ubi0 -s 2GiB -N root

mount /dev/ubi0_0 /mnt/ -t ubifs

root@cubieboard:~# mount /dev/ubi0_0 /mnt/ -t ubifs
[Wed Feb 28 17:49:38 2018] UBIFS error (pid: 4709): cannot open "/dev/ubi0:root", error -22
[Wed Feb 28 17:49:43 2018] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 4722
[Wed Feb 28 17:49:44 2018] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "root"
[Wed Feb 28 17:49:44 2018] UBIFS (ubi0:0): LEB size: 1032192 bytes (1008 KiB), min./max. I/O unit sizes: 8192 bytes/8192 bytes
[Wed Feb 28 17:49:44 2018] UBIFS (ubi0:0): FS size: 2137669632 bytes (2038 MiB, 2071 LEBs), journal size 33030144 bytes (31 MiB, 32 LEBs)
[Wed Feb 28 17:49:44 2018] UBIFS (ubi0:0): reserved for root: 4952683 bytes (4836 KiB)
[Wed Feb 28 17:49:44 2018] UBIFS (ubi0:0): media format: w5/r0 (latest is w5/r0), UUID 8E9A30F0-241F-4013-916F-C0B995F22BB1, small LPT model


cubieboard2

This is mostly redundant from cubieboard, but with attempt to define mtd partitions correctly

root@cubieboard2:/home/dpavlin# ubiformat /dev/mtd0
ubiformat: mtd0 (mlc-nand), size 4273995776 bytes (4.0 GiB), 2038 eraseblocks of 2097152 bytes (2.0 MiB), min. I/O size 8192 bytes
libscan: scanning eraseblock 2037 -- 100 % complete  
ubiformat: 2038 eraseblocks have valid erase counter, mean value is 1
ubiformat: formatting eraseblock 2037 -- 100 % complete  



mount ubifs filesystem

dpavlin@cubieboard:~$ grep ubi /mnt/boot/armbianEnv.txt
rootdev=ubi0:root ubi.mtd=0
rootfstype=ubifs

dpavlin@cubieboard:~$ grep ubi /etc/fstab 
ubi0:root / ubifs defaults,noatime,nodiratime 0 1

u-boot

Original u-boot output

HELLO! BOOT0 is starting!
boot0 version : 1.5.1
dram size =1024
Succeed in opening nand flash.
Succeed in reading Boot1 file head.
The size of Boot1 is 0x0003c000.
The file stored in 0X00000000 of block 2 is perfect.
Check is correct.
Ready to disable icache.
Succeed in loading Boot1.
Jump to Boot1.
[       0.133] boot1 version : 1.4.0
[       0.133] pmu type = 3
[       0.134] bat vol = 0
[       0.161] axi:ahb:apb=3:2:2
[       0.161] set dcdc2=1400, clock=1008 successed
[       0.163] key
[       0.175] no key found
[       0.175] flash init start
[       4.051] flash init finish
[       4.052] fs init ok
[       4.053] fattype FAT16
[       4.053] fs mount ok
[       4.060] script finish
[       4.061] power finish
[       4.069] BootMain start
[       4.069] 13
[       4.089] key value = 0
[       4.089] recovery key high 6, low 4
[       4.090] unable to find fastboot_key key_max value
[       4.098] test for multi os boot with display
[       4.100] show pic finish
[       4.103] load kernel start
[       4.127] load kernel successed
[       4.127] start address = 0x4a00000

U-Boot 2011.09-rc1 (Nov 26 2012 - 14:01:52) Allwinner Technology 

CPU:   SUNXI Family
Board: A10-EVB
DRAM:  512 MiB
NAND:  3776 MiB
In:    serial
Out:   serial
Err:   serial
--------fastboot partitions--------
-total partitions:11-
-name-        -start-       -size-      
bootloader  : 1000000       1000000     
env         : 2000000       1000000     
boot        : 3000000       2000000     
system      : 5000000       14000000    
data        : 19000000      20000000    
misc        : 39000000      1000000     
recovery    : 3a000000      2000000     
cache       : 3c000000      8000000     
private     : 44000000      1000000     
sysrecovery : 45000000      14000000    
UDISK       : 59000000      93000000    
-----------------------------------
Hit any key to stop autoboot:  0 
sunxi#

compile with nand support

On Cubieboard2 with those patches we get:

=> nand info

Device 0: nand0, sector size 2048 KiB
  Page size       8192 b
  OOB size         640 b
  Erase size   2097152 b
  subpagesize     8192 b
  options     0x00001000
  bbt options 0x00070000

# which comparted to booted linux kernel with mtd support....

root@cubieboard2:~# mtd_debug info /dev/mtd0
mtd.type = MTD_MLCNANDFLASH
mtd.flags = MTD_CAP_NANDFLASH
mtd.size = 4284481536 (3G)
mtd.erasesize = 2097152 (2M)
mtd.writesize = 8192 (8K)
mtd.oobsize = 640 
regions = 0

# it looks somewhat OK, but mtdparts doesn't (yet) return anything.

Another day, another try to get mtdparts to display something...

root@armbian:~/build/cache/sources/u-boot/v2017.11# grep -i mtd .config
CONFIG_SPL_MTD_SUPPORT=y
CONFIG_CMD_MTDPARTS=y
CONFIG_MTDIDS_DEFAULT="nand0=sunxi-nand"
CONFIG_MTDPARTS_DEFAULT="mtdparts=sunxi-nand:4m(spl),4m(spl-backup),4m(uboot),4m(uboot-backup),4m(env),-(UBI)"
# CONFIG_CMD_MTDPARTS_SPREAD is not set
# MTD Support
CONFIG_MTD=y
# CONFIG_MTD_NOR_FLASH is not set
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_WL_THRESHOLD=4096
CONFIG_MTD_UBI_BEB_LIMIT=20
# CONFIG_MTD_UBI_FASTMAP is not set

=> mtdparts

device nand0 <sunxi-nand>, # parts = 6
 #: name                size            offset          mask_flags
 0: spl                 0x00400000      0x00000000      0
 1: spl-backup          0x00400000      0x00400000      0
 2: uboot               0x00400000      0x00800000      0
 3: uboot-backup        0x00400000      0x00c00000      0
 4: env                 0x00400000      0x01000000      0
 5: UBI                 0xfec00000      0x01400000      0

active partition: nand0,0 - (spl) 0x00400000 @ 0x00000000

defaults:
mtdids  : nand0=sunxi-nand
mtdparts: mtdparts=sunxi-nand:4m(spl),4m(spl-backup),4m(uboot),4m(uboot-backup),4m(env),-(UBI)







Instructions after this are hit-or-miss...

dpavlin@klin:/klin/u-boot$ cp configs/Cubieboard_defconfig .config

# add NAND, MTD options, A10 for cubieboard1

# compile while defining flash:

dpavlin@klin:/klin/u-boot$ cat build-cubieboard.sh 
# parametars are probably wrong for your chip!
make V=1 CONFIG_NAND_SUNXI_SPL_ECC_STRENGTH=40 CONFIG_SYS_NAND_PAGE_SIZE=4036 CONFIG_SYS_NAND_OOBSIZE=640 CONFIG_SYS_NAND_BLOCK_SIZE=0x100000


dpavlin@cubieboard:~$ scp 10.60.0.92:/klin/u-boot/u-boot*spl* .

dpavlin@cubieboard:~$ sudo dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblk0 bs=1024 seek=8 
488+1 records in
488+1 records out
500154 bytes (500 kB) copied, 0.0423498 s, 11.8 MB/s


It would be better to define params in u-boot config file like:

CONFIG_SYS_EXTRA_OPTIONS="SYS_NAND_BLOCK_SIZE=0x40000,SYS_NAND_PAGE_SIZE=4096,SYS_NAND_OOBSIZE=256"

(with correct values of course).

pinout

U14 (Next to SATA connector)

  SPI0
48 PI13 (SPI0-MISO/UART6-RX/EINT25) 47 PI11 (SPI0-CLK/UART5-RX/EINT23)
46 PI12 (SPI0-MOSI/UART6-TX/EINT24) 45 PI10 (SPI0-CS/UART5-TX/EINT22)
  LCD
44 3.3V (nc in 2012-08-08) 43 VCC-5V
42 Ground 41 SPDIF
40 PB10 (LCD0-SCK/LCD-PIO1) 39 PB11 (LCD0-SDA/LCD-PIO2)
38 Ground 37 PH7 (LCD0-BL-EN/LCD-PIO0/UART5-RX/EINT7)
36 XN_TP (TP-X2) 35 YN_TP (TP-Y2)
34 XP_TP (TP-X1) 33 YP_TP (TP-Y1)
32 PD25 (LCDDE) 31 PB2 (PWM0)
30 PD26 (LCDHSYNC)-VGA-HSYNC 29 PD24 (LCDCLK)
28 PD23 (LCDD23) 27 PD27 (LCDVSYNC)-VGA-VSYNC
26 PD21 (LCDD21) 25 PD22 (LCDD22)
24 PD19 (LCDD19/LVDS1N3) 23 PD20 (LCDD20)
22 PD17 (LCDD17/LVDS1NC) 21 PD18 (LCDD18/LVDS1P3)
20 Ground 19 PD16 (LCDD16/LVDS1PC)
18 PD14 (LCDD14/LVDS1P2) 17 PD15 (LCDD15/LVDS1N2)
16 PD12 (LCDD12/LVDS1P1) 15 PD13 (LCDD13/LVDS1N1)
14 PD10 (LCDD10/LVDS1P0) 13 PD11 (LCDD11/LVDS1N0)
12 PD8 (LCDD8/LVDS0P3) 11 PD9 (LCDD9/LVDS0N3)
10 PD7 (LCDD7/LVDS0NC) 9 Ground
8 PD5 (LCDD5/LVDS0N2) 7 PD6 (LCDD6/LVDS0PC)
6 PD3 (LCDD3/LVDS0N1) 5 PD4 (LCDD4/LNVS0P2)
4 PD1 (LCDD1/LVDS0N0) 3 PD2 (LCDD2/LVDS0P1)
2 Ground 1 PD0 (LCDD0/LVDSP0)

U15 (Between Ethernet port and USB ports)

  CSI1/TS
1 VCC-5V 2 PH15 (CSI1-PWR/EINT15)
3 CSI1-IO-2V8 4 PH14 (CSI1-RST#/EINT14)
5 PG0 (CSI1-PCLK/SDC1-CMD) 6 PB18 (TWI1-SCK)
7 PB19 (TWI1-SDA) 8 PG3 (CSI1-VSYNC/SDC1-D1)
9 PG2 (CSI1-HSYNC/SDC1-D0) 10 PG1 (CSI1-MCLK/SDC1-CLK)
11 PG4 (CSI1-D0/SDC1-D2) 12 PG5 (CSI1-D1/SDC1-D3)
13 PG6 (CSI1-D2/UART3-TX) 14 PG7 (CSI1-D3/UART3-RX
15 PG8 (CSI1-D4/UART3-RTS) 16 PG9 (CSI1-D5/UART3-CTS)
17 PG10 (CSI1-D6/UART4-TX) 18 PG11 (CSI1-D7/UART4-RX)
19 Ground 20 Ground
  Analog SDIO3
21 FMINL 22 PI4 (SDC3-CMD)
23 FMINR 24 PI5 (SDC3-CLK)
25 Ground 26 PI6 (SDC3-D0)
27 VGA-R 28 PI7 (SDC3-D1)
29 VGA-G 30 PI8 (SDC3-D2)
31 VGA-B 32 PI9 (SDC3-D3)
  CSI0/TS
33 LCD1-VSYNC 34 PE4 (CSI0-D0)
35 LCD1-HSYNC 36 PE5 (CSI0-D1)
37 Ground 38 PE6 (CSI0-D2)
39 AVCC 40 PE7 (CSI0-D3)
41 LRADC0 42 PE8 (CSI0-D4)
43 CVBS 44 PE9 (CSI0-D5)
45 HPL 46 PE10 (CSI0-D6)
47 HPR 48 PE11 (CSI0-D7)


everything below line is for legacy kernel and quite old

disk speed

NAND

root@cubieboard2:/home/dpavlin# uname -a
Linux cubieboard2 3.4.109-sun7i #4 SMP PREEMPT Sun Oct 11 14:32:15 CEST 2015 armv7l GNU/Linux
root@cubieboard2:/home/dpavlin# hdparm -t /dev/nand

/dev/nand:
 Timing buffered disk reads:  32 MB in  3.22 seconds =   9.94 MB/sec

# this is different, faster sdcard
root@cubieboard2:~# uname -a
Linux cubieboard2 4.3.3-sunxi #3 SMP Mon Dec 28 11:27:16 CET 2015 armv7l GNU/Linux
root@cubieboard2:~# hdparm -tT /dev/mmcblk0

/dev/mmcblk0:
 Timing cached reads:   770 MB in  2.00 seconds = 384.59 MB/sec
 Timing buffered disk reads:  60 MB in  3.05 seconds =  19.67 MB/sec



SATA

Powered by 2A Nexus 7 power supply (for SATA)

https://groups.google.com/d/searchin/cubieboard/sata/cubieboard/hKJgJneGVmQ/xme3w4Y7XtsJ?fromplusone=1

root@debian:~/sunxi-tools# ./bin2fex /boot/script.bin script.fex
fexc-bin: /boot/script.bin: version: 0.1.2
fexc-bin: /boot/script.bin: size: 42144 (76 sections)

root@debian:~/sunxi-tools# cp script.fex script+sata.fex

root@debian:~/sunxi-tools# diff -urw script.fex script+sata.fex 
--- script.fex  2013-05-30 10:41:13.979510762 +0000
+++ script+sata.fex     2013-05-30 10:42:36.380244101 +0000
@@ -595,7 +595,7 @@
 
 [sata_para]
 sata_used = 1
-sata_power_en =
+sata_power_en = port:PB08<1><default><default><0>
 
 [mmc0_para]
 sdc_used = 1

root@debian:~/sunxi-tools# ./fex2bin script+sata.fex /boot/script.bin

root@debian:/etc# git diff
diff --git a/modules b/modules
index d8894c3..9e65a80 100644
--- a/modules
+++ b/modules
@@ -4,3 +4,4 @@
 # at boot time, one per line. Lines beginning with "#" are ignored.
 # Parameters can be specified after the module name.
 
+sw_ahci_platform

Reboot to activate changes and test speed (using 80G intel SSD to have sense of maximum performance)

root@debian:~# hdparm -i /dev/sda

/dev/sda:

 Model=INTEL SSDSA2M080G2GC, FwRev=2CV102HD, SerialNo=CVPO035101VN080JGN
 Config={ Fixed }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
 BuffType=unknown, BuffSize=unknown, MaxMultSect=16, MultSect=1
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6 
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: ATA/ATAPI-7 T13 1532D revision 1:  ATA/ATAPI-2,3,4,5,6,7

 * signifies the current active mode

root@debian:~# hdparm -tT /dev/sda

/dev/sda:
 Timing cached reads:   784 MB in  2.00 seconds = 392.08 MB/sec
 Timing buffered disk reads: 460 MB in  3.00 seconds = 153.32 MB/sec

And test with disk:

root@debian:~# hdparm -i /dev/sda

/dev/sda:

 Model=ST96812AS, FwRev=7.24, SerialNo=3PJ1GCKE
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=off
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=117231408
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 
 AdvancedPM=yes: unknown setting WriteCache=enabled
 Drive conforms to: Unspecified:  ATA/ATAPI-1,2,3,4,5,6,7

 * signifies the current active mode

root@debian:~# hdparm -tT /dev/sda

/dev/sda:
 Timing cached reads:   746 MB in  2.00 seconds = 372.90 MB/sec
 Timing buffered disk reads: 120 MB in  3.03 seconds =  39.56 MB/sec

GPIO

Camera

OV7670 is supported http://linux-sunxi.org/CSI

hardware

pinout: gpio_defination_large.jpg

https://www.olimex.com/wiki/How_to_add_pwm

cat /sys/class/pwm-sunxi/pwm0/pin 
PB2

echo 10khz > /sys/class/pwm-sunxi/pwm0/period

echo 25 > /sys/class/pwm-sunxi/pwm0/duty_percent

echo 1 > /sys/class/pwm-sunxi/pwm0/run

LEDs

dpavlin@cubieboard2:~$ grep . /sys/class/leds/*/trigger 
/sys/class/leds/blue:ph21:led2/trigger:none battery-charging-or-full battery-charging battery-full battery-charging-blink-full-solid ac-online usb-online mmc0 timer [heartbeat] backlight cpu0 cpu1 default-on 
/sys/class/leds/green:ph20:led1/trigger:[none] battery-charging-or-full battery-charging battery-full battery-charging-blink-full-solid ac-online usb-online mmc0 timer heartbeat backlight cpu0 cpu1 default-on 

forum

ina219

device tree

dpavlin@cubieboard2:~$ sensors
ina219-i2c-1-40
Adapter: mv64xxx_i2c adapter
in0:          +0.04 V  
in1:          +4.64 V  
power1:       66.88 W  
curr1:       +13.64 A  

iio_hwmon-isa-0000
Adapter: ISA adapter
temp1:        +33.6�C  

root@cubieboard2:~# dmesg | grep ina | tail -1
[ 6597.685287] ina2xx 1-0040: power monitor ina219 (Rshunt = 100 uOhm)

# hum, it should be 10uA, so I changed that in device tree

dpavlin@cubieboard2:~$ dmesg | grep ina219
[   11.594536] ina2xx 1-0040: power monitor ina219 (Rshunt = 10 uOhm)
dpavlin@cubieboard2:~$ sensors
ina219-i2c-1-40
Adapter: mv64xxx_i2c adapter
in0:          +0.02 V  
in1:          +4.75 V  
power1:       85.00 W  
curr1:       +17.97 A  

iio_hwmon-isa-0000
Adapter: ISA adapter
temp1:        +32.5�C  

# still wrong current!


user-land C

User-land implementation which works: https://github.com/ZigFisher/Glutinium/blob/master/i2c-telemetry/src/ina219.c

modified a little to provide full timestamp and fflush: ina219.c

dpavlin@cubieboard2:~$ ./ina219 -b 1 -i 1
2017-10-23T12:40:24 4744mV  262.2mA
2017-10-23T12:40:26 4756mV  249.1mA
2017-10-23T12:40:27 4776mV  223.0mA
2017-10-23T12:40:28 4772mV  223.8mA
2017-10-23T12:40:29 4760mV  224.0mA
2017-10-23T12:40:30 4768mV  223.0mA
2017-10-23T12:40:31 4772mV  223.1mA
2017-10-23T12:40:32 4748mV  224.6mA
2017-10-23T12:40:33 4776mV  223.1mA
2017-10-23T12:40:34 4768mV  223.5mA

SPI flash

flashrom

dpavlin@cubieboard:~$ sudo grep spidev /boot/armbianEnv.txt
overlays=pwm nand uart3 uart4 spi-spidev
#overlays=spi-spidev
param_spidev_spi_bus=0


dpavlin@cubieboard:~$ sudo flashrom -p linux_spi:dev=/dev/spidev0.0
flashrom v0.9.9-2-g51e4303 on Linux 4.14.47-sunxi (armv7l)
flashrom is free software, get the source code at https://flashrom.org

Calibrating delay loop... OK.
Found GigaDevice flash chip "GD25Q80(B)" (1024 kB, SPI) on linux_spi.
No operations were specified.

root@cubieboard:/home/dpavlin# time flashrom -p linux_spi:dev=/dev/spidev0.0 -r /dev/null
flashrom v0.9.9-2-g51e4303 on Linux 4.14.47-sunxi (armv7l)
flashrom is free software, get the source code at https://flashrom.org

Calibrating delay loop... OK.
Found GigaDevice flash chip "GD25Q80(B)" (1024 kB, SPI) on linux_spi.
Reading flash... done.

real    0m11.210s
user    0m0.796s
sys     0m0.381s


build u-boot with SPI support

http://linux-sunxi.org/Bootable_SPI_flash

git clone -b sunxi-spi https://github.com/StephanvanSchaik/u-boot

dpavlin@armbian:~/u-boot$ git diff
diff --git a/configs/Cubieboard_defconfig b/configs/Cubieboard_defconfig
index 0389d4c..cbafac9 100644
--- a/configs/Cubieboard_defconfig
+++ b/configs/Cubieboard_defconfig
@@ -16,3 +16,13 @@ CONFIG_SPL=y
 # CONFIG_SPL_ISO_PARTITION is not set
 # CONFIG_SPL_EFI_PARTITION is not set
 CONFIG_USB_EHCI_HCD=y
+
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_DM_SPI=y
+CONFIG_SUNXI_SPI=y
+
dpavlin@armbian:~/u-boot$ make Cubieboard_defconfig




This doesn't actually work for me (since it's missing device tree overlays), but rebasing to current u-boot master doesn't
produce code which compiles.

https://forum.armbian.com/topic/3252-opi-zero-boot-with-spi/

reset

http://linux-sunxi.org/Cubieboard/Reset