Java remote console client ftp://ftp.supermicro.com/utility/IPMIView/Linux/
ftp://ftp.supermicro.com/utility/IPMIView/Jar/IPMIView20-Class_v2.8.0_Build110802.zip
Real installation is endless pain and won't work (for me).
dpavlin@klin:/opt$ wget ftp://ftp.supermicro.com/utility/IPMIView/Jar/IPMIView2-Class_v2.8.0_Build110802.zip dpavlin@klin:/opt$ unzip IPMIView20-Class_v2.8.0_Build110802.zip -d IPMIView dpavlin@klin:/opt$ cd IPMIView/ dpavlin@klin:/opt/IPMIView$ chmod 755 IPMIView20.sh
According to http://www.mcgill.org.za/stuff/archives/340 you should be able to run KVM stand alone:
java -cp .:::::$PWD/iKVM.jar:$PWD/IPMIView20.jar:$PWD/TrapView.jar:::::: \ -Djava.library.path=. \ -D tw.com.aten.ikvm.KVMMain \ $IP $USERNAME $PASSWORD null 5900 623 2 0 java -Djava.library.path=. -jar iKVM.jar \ $IP $USERNAME $PASSWORD null 5900 623 2 0
dpavlin@porn:~$ dmesg | grep ib [ 0.000000] Fast TSC calibration using PIT [ 0.000002] Calibrating delay loop (skipped), value calculated using timer frequency.. 6185.92 BogoMIPS (lpj=12371840) [ 0.764371] vgaarb: bridge control possible 0000:06:03.0 [ 1.261922] PM: Hibernation image not present or could not be loaded. [ 1.311730] libata version 3.00 loaded. [ 1.948194] Refined TSC clocksource calibration: 3092.973 MHz. [ 17.345807] ib_mthca: Mellanox InfiniBand HCA driver v1.0 (April 4, 2008) [ 17.345810] ib_mthca: Initializing 0000:04:00.0 [ 17.345827] ib_mthca 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 17.345841] ib_mthca 0000:04:00.0: setting latency timer to 64 [ 18.547370] ib_mthca 0000:04:00.0: HCA FW version 4.7.600 is old (4.8.200 is current). [ 18.547373] ib_mthca 0000:04:00.0: If you have problems, try updating your HCA FW. [ 18.547538] ib_mthca 0000:04:00.0: irq 51 for MSI/MSI-X [ 18.547542] ib_mthca 0000:04:00.0: irq 52 for MSI/MSI-X [ 18.547546] ib_mthca 0000:04:00.0: irq 53 for MSI/MSI-X dpavlin@porn:~$ cat /sys/class/infiniband/mthca0/ports/1/state 4: ACTIVE dpavlin@porn:~$ cat /sys/class/infiniband/mthca0/ports/1/rate 20 Gb/sec (4X DDR) dpavlin@porn:~$ cat /sys/class/infiniband/mthca0/ports/1/phys_state 5: LinkUp dpavlin@porn:~$ cat /sys/class/infiniband/mthca0/ports/2/phys_state 2: Polling
disks seem to move from boot to boot so we need to specify disks for pool using persistant IDs:
zpool create -f test raidz3 `ls /dev/disk/by-id/ata-Hitachi_HDS723030ALA640_MK03* | grep -v part`
http://groups.google.com/a/zfsonlinux.org/group/zfs-discuss/browse_thread/thread/2a822bb27a1cdce5
hdparm I, specifically, will give you the serial number and http://sg.danny.cz/sg/smp_utils.html.
lsscsi/lsblk would probably be helpful here with topology. Lighting a
bay LED without relying on guessing which drive you're doing i/o is
doable, but more dependent on your specific adapter's tools available.
See also: smp_utils
Setting the fault or identify leds can be done with the sg3_utils
package and a carefully crafted SES command. Alternately, if you load
the SES kernel module you can set them via the fault and locate sysfs
entries.
ls /sys/devices/pci0000:00/0000:00:0f.0/0000:07:00.0/host6/port-6:0/expander-6 :0/port-6:0:17/end_device-6:0:17/target6:0:16/6:0:16:0/enclosure/6:0:16:0/S LOT\ 000
active device fault locate power status type uevent